Summary of June 2000 CERN ISR Test Data

Updated : 19 July 2000 RL

The following table summarizes the conditions of the data taken for the June 2000 CERN ISR Test. It is primarily based on notations made in the FNAL logbook, but also makes use of the output log files, Event and Begin Run records, and headers of the datafiles. You can find a sequential listing of all datafile headings and Begin Run records here. It is highly recommended you examine the Begin Run Records and Event Records of the data sets for a better understanding of the DAQ settings during a particular run. A page to help you decode the Begin Run and Event Records are here.

You can find the June 2000 ISR Test Data Description here.

Notes:

Almost all runs have random errors from DSP output. Some lines are cut, some headers and important markers were lost. These runs should be check prior to FLAP processing.
Runs that were corrupted or had abnormal terminations have been marked in the table, but the files are simply too large to look for errors in data or data formating.
There are many more notations and relevant information in the FNAL logbook. This table is only a summary is some information.

Runs which have been checked and/or corrected are marked in YELLOW.

	Initial System Setup and Diagnostics
RData 210	LDM Power off, 6 sensors
RData 211	LDM Power on, 6 sensors
RData 212	error w/ DCOPS (2 trys)
RData 323	new daq configuration, failed self test
RData324	corrupt data w/ 14 sensors
RData325	7 sensors, missing #0001 characters and sensor 1 data seems high
RData 326	6 sensors, run looks ok
RData 327	10 sensors, readout is ok, 10 cycles w/ 1 event per cycle (5 sec delay)
	HP Unit Disconnected – Manual LDM Operation
RData 328	First trial w/ no Data Second Trial w/ HP Disconnected, manual LDM operation (left on) 10 sensors connected
RData 329	Test w/ HP Disconnected
RData 330	Testing 13 sensor readout 1 event, data looks like empty buffers (no bkground)
RData 331	Testing 13 sensor readout 4 events, data looks like empty buffers
RData 332	Testing 13 sensor readout 20 events, data looks like empty buffers
RData 333	Test w/ HP Disconnected
RData 334	Test w/ HP Disconnected
RData 335	Test w/ HP Disconnected
RData 336	Test w/ HP Disconnected
RData 337	Test w/ HP Disconnected
RData 338	Test w/ HP Disconnected
RData 339	Axial Line Readout – No HP Data
RData 340	Axial Line Readout w/ HP Data
RData 341	et0 readout only – looks like bkg only(?)
RData 342	et0 readout only, 1 event
	Axial Line Surveyed, es7 micrometer moved from 2.90 -> 2.00
RData 343	20 cycles full Axial Line, No HP Data or Lasers On Data, abnormal termination after 16 cycles
RData 344	Aborted as test
	Axial Line Complete - Axial Line Data Only w/ HP Unit Operational
RData 345	20 clusters, 1 event, 20 sec delay, 5 sec LDM warmup
RData 346	20 clusters, 1 event, 20 sec delay, 5 sec LDM warmup (small software correction)
RData 347	1 clusters, 20 events 5 sec LDM warmup
RData 348	Single Shot Axial Line
RData 349	Single Shot Axial Line
RData 350	Single Shot Axial Line
RData 351	Single Shot Axial Line
RData 352	Single Shot Axial Line
RData 353	Axial LDM has been cold 3 hours, doghouses put on et 3&4, Lights off, 20 cycles of quick data on Axial Line only
	SLM Line Setup and Drilled Down
RData 354	Full SLM line – 1 shot 13 sensors board reset in first event
RData 355	Full SLM line + Axial line 10 clusters, 4 events per cluster, 60 sec interval abnormal termination, board reset in first event
RData 356	Full SLM line + Axial line 2 x 1 shot Readout w/ Wux and CC Failed
	Splitting Lines into SLM and Axial Lines Single Directional only unless noted
RData 357	SLM Laser 303 – 5 events
RData 358	2 sensor stability s6 and s1 (es10 & es5) 20 Quick Measurements to compare peak quality and resolution of a ‘poor’ sensor (s1) and a ‘good’ one (s6) No end run record, but data looks like it acquired ok
RData 359	2 sensor stability s6 and s1 (es10 & es5) 10 Quick Measurements to compare peak quality and resolution of a ‘poor’ sensor (s1) and a ‘good’ one (s6)
RData 360	2 sensor stability s6 and s1 (es10 & es5) 10 Quick Measurements to compare peak quality and resolution of a ‘poor’ sensor (s1) and a ‘good’ one (s6)
RData 361	Full SLM w/ 5 events Abnormal termination in event 1
RData 362	Single Shot SLM 8 sensors readout
RData 363	Single Shot SLM 8 sensors readout
RData 364	2 Clusters SLM 1 Shot each
RData 365	SLM Line 60 Clusters, 1 event per cluster, 30 sec LDM warmup, No end run record but readout of 60 clusters seems complete At least through #0002 of last event in last cluster
RData 366	Aborted
RData 370	Axial Line Single Shot Background Only (LDM was unplugged) 5 Sensors
RData 371	Axial Line 13 sensors connected, 5 readout Cold laser, lights on, middle of afternoon
RData 372	Axial Line ( 5 sensors connected, 5 readout only) 25 cycles looking at LDM warmup again - Lights on, Doghouses on Data initially has extra lines from DSP responses, but it appears limited to first event
RData 373	Axial Line ( 5 sensors connected, 5 readout only) 20 cycles looking at LDM warmup again - Lights on, Doghouses on Data looks ok
	Final SLM Tape Configuration Applied
RData 374	Axial Line 10 clusters w/ 3 events per cluster Computer hung after completion – Data looks ok on simple inspection
RData 375	Axial Line running overnight 20 clusters w/ 4 events per cluster 60 sec spacing, 30 sec ldm warmup Run aborted early upon return the next morning. 15/20 Clusters completed
	Back to Single DCOPS String of 13 Sensors for SLM + Axial Lines
RData 376	13 sensors Bi-Directional Laser 301 tied to Laser 303 4 Clusters 10:1 Laser ON:Laser OFF events 540 sec between clusters, 30 sec LDM warmup 84 events read
	Laser 301 now tied to Laser 303 AND Laser 302 Permanently
RData 377	13 sensors Bi-Directional Laser 301 tied to Laser 303 AND Laser 302 Single Shot
RData 378	13 sensors Bi-Directional 2 Clusters w/ 2 events each No time delay between clusters
RData 379	13 sensors Bi-Directional Long Overnight Run 70 Clusters 5:1 Laser ON:Laser OFF events 150 sec between clusters, 30 sec LDM delay Killed next morning before lights turned on 38.5 clusters ok – Lights on at cluster 34; cluster 22 & 32 not corrected
RData 380	Short Axial Run 20 clusters, 5 sensors only 60 sec delay, 30 sec LDM warmup
RData 381	Short Test Run SLM + Axial Bi Directional 1 cluster w/ 1:1 laser on:laser off
RData 382	13 sensors Bi-Directional 2 Clusters, 3:1 Laser ON:Laser OFF events 90 sec delay, 30 sec LDM Warmup
	Sensors Are Now Being Moved (RData 382 is original position)
RData 383	et2 moved +1mm in +X direction (New position is 6mm) Bi-Dir 2 Clusters w/ 4 Laser On per cluster 90 sec delay, 30 sec LDM warmup Only 8 events taken (Single Shot Mode by mistake)
RData 384	Repeating 383 Bi-Dir 2 Clusters w/ 4 Laser On per cluster 90 sec delay, 30 sec LDM warmup 16 events taken
RData 385	et2 moved +1mm in +X direction (New position is 7mm) Bi-Dir 2 Clusters w/ 4 Laser On per cluster 90 sec delay, 30 sec LDM warmup Z Sensor on MAB is lost now from change in position System hung after 3 events
RData 386	Repeating 385 Bi-Dir 2 Clusters w/ 4 Laser On per cluster 90 sec delay, 30 sec LDM warmup Z Sensor on MAB is lost now from change in position System hung after 3 events
RData 387	et2 moved back to original position Bi-Dir 2 Clusters w/ 4 Laser On per cluster 90 sec delay, 30 sec LDM warmup
RData 388	et2 moved -1mm in X direction Bi-Dir 2 Clusters w/ 4 Laser On per cluster 90 sec delay, 30 sec LDM warmup
	Motion Shift Studies on SLM Line et2 moved back to 0 All Data taken with 2 Clusters, 4 events per Cluster w/ Laser ON 90 sec delay, 30 sec LDM warmup
RData 389	es5 moved 100 um in +Z (4 notches) Previous position: .050 New Position: .054
RData 390	es5 moved 100 um in +Z (New Position: .058)
RData 391	es5 moved 100 um in +Z
RData 392	Back to .054
RData 393	Back to Original position (.050)
RData 394	es5 moved 100 um in -Z (New Position: .046) 1 event only
RData 395	Retry 394 w/ proper number clusters and events (described above)
RData 396	Original micrometer position Aborted after 4 events by user (1 shot was intended)
RData 397	Repeat 396 but w/ One Shot Only
RData 398	Reading S5 only Moving 20 notches tp .5mm
RData 399	Reading S5 only - One Shot at .055
RData 400	Reading S5 only - One Shot at .045
	Ending Shift Studies
RData 401	Long Run 18 Clusters 4 Events per Cluster 90 sec delay, 30 sec LDM warmup Lights Off w/ Doghouses on et 3&4 72 events read, but no end run record
	Looking at Shifts once Again
RData 402	1 Shot of es5 (original position) Lights On / Dog Houses On ** We have had problems w/ micrometer (see log book pg 73) Micrometer original position is .00505
RData 403	1 Shot of es5 3 sec LDM warmup
RData 404	1 Shot of es5 30 sec LDM warmup
RData 405	1 Shot of es5 30 sec LDM warmup
RData 406	1 Shot of es5 30 sec LDM warmup
RData 407	1 Shot of es5 30 sec LDM warmup
RData 408	1 Shot of es5 30 sec LDM warmup
RData 409	1 Shot of es5 30 sec LDM warmup
RData 410	es5 Micrometer moved to .00495 One shot 30 sec LDM warmup
RData 411	es5 Micrometer moved to .00400 (CERN photogrametry position) One shot 30 sec LDM warmup
RData 412	Micrometer at .0000 1 shot es5 30 sec LDM warmup (Lights ON and Saturated Sensor)
RData 413	Micrometer at .0000 1 shot es5 30 sec LDM warmup
RData 414	Moving 4 notches on es5 to .0004 Es4 read out by mistake
RData 415	es5 at .0004 es5 readout only
RData 416	es5 at .0008 es5 readout only – forgot doghouse, saturated
RData 417	es5 at .0008 es5 readout only
RData 418	es5 at .0040 (moved 10*4 notches) es5 readout only
RData 419	es5 at .0000 es5 readout only
RData 420	es7 original position at .2001 One Shot of es7
RData 421	Es7 moved to .2005 One Shot of es7 in Bi-Directional mode Lights On w/ Doghouses
RData 422	Es7 moved to .2005 2 Clusters of es7 in Bi-Directional mode Lights Off w/ Doghouses 90 sec interval, 30 sec LDM warmup
RData 423	Es7 moved to .2005 One Shot of es7 in Bi-Directional mode Lights On w/ Doghouses
RData 424	Single Shot of es7 w/ micrometer at .2001
RData 425	Single Shot of es7 w/ micrometer at .2005
RData 426	Single Shot of es7 w/ micrometer at .2041
RData 427	Single Shot of es7 w/ micrometer at .2001
RData 428	Single Shot of es7 w/ micrometer at .2021
RData 429	Single Shot of es7 w/ micrometer at .2001
RData 430	Single Shot of es7 w/ micrometer at .1997
RData 431	Single Shot of es7 w/ micrometer at –40 notches from .2001
RData 432	Single Shot of es7 w/ micrometer at .2001 (original position)
RData 433	Single Shot of es7 w/ micrometer at –20 notches 2000
RData 434	Single Shot of es7 w/ micrometer at .2001 (original position)
RData 435	Single Shot of es7 w/ micrometer at .2001 (original position)
	Interupting Shift Studies for a Break …
RData 436	Full SLM + Axial Line 13 Sensors Bi-Directional 6 Clusters 4:0 Laser ON: Laser Off 90 sec interval w/ 30 sec LDM warmup Lights off (es7 micometer at .2001)
	Returning to look at Shifts
RData 437	Single shot only, check to see if laser is moving, es7 micrometer at .2001 es3, es5, and es6 read out only error in es3 – bad fit parameter
RData 438	Single shot only, check to see if laser is moving, es7 micrometer at .2001 es3, es5, and es6 read out only
RData 439	Single Shot (es 4-7 readout only) es7 -> +8 clicks to .2009 es6 es5 -> +8 clicks to .0008 es4
RData 440	Single Shot (es 4-7 readout only) es7 -> +20 clicks to .2021 es6 es5 -> +20 clicks to .0020 es4
RData 441	Single Shot (es 4-7 readout only) es7 -> +40 clicks to .2041 es6 es5 -> +40 clicks to .0040 es4
RData 442	Single Shot (es 4-7 readout only) es7 back at original position (.2001) es6 es5 back at original position (.0000) es4
	Finished with Shift Studies
RData 443	3 Quick Bi-Directional Events Full SLM + Axial Line 13 sensors
RData 444	3 Quick Bi-Directional Events Full SLM + Axial Line 13 sensors
	Looking at LDM warmup in LDM302 & LDM301 Single Shot SLM + Axial Line 13 Sensors
RData 445	2 sec warmup time
RData 446	4 sec warmup time
RData 447	6 sec warmup time
RData 448	8 sec warmup time
RData 449	15 sec warmup time
RData 450	20 sec warmup time
RData 451	40 sec warmup time
RData 452	60 sec warmup time
RData 453	75 sec warmup time
RData 454	90 sec warmup time
RData 455	110 sec warmup time
RData 456	180 sec warmup time
	End of June 2000 ISR Testing at CERN

Initial System Setup and Diagnostics

HP Unit Disconnected – Manual LDM Operation

Axial Line Surveyed, es7 micrometer moved from 2.90 -> 2.00

Axial Line Complete - Axial Line Data Only w/ HP Unit Operational

Splitting Lines into SLM and Axial Lines

Single Directional only unless noted

Final SLM Tape Configuration Applied

Back to Single DCOPS String of 13 Sensors for SLM + Axial Lines

Laser 301 now tied to Laser 303 AND Laser 302 Permanently

Sensors Are Now Being Moved (RData 382 is original position)

Motion Shift Studies on SLM Line

Ending Shift Studies

Looking at Shifts once Again

Interupting Shift Studies for a Break …

Full SLM + Axial Line

Finished with Shift Studies

Looking at LDM warmup in LDM302 & LDM301

End of June 2000 ISR Testing at CERN